Wheels "stunned" to eliminate
5XZS series seed cleaning & processing machine is the combined grain seed cleaning equipment. It installed wheat huller,
air cleaning screen, vibration pre cleaning sieve, gravity table, vibration
sieve cleaning and grading trunk. It maximizes one machine cleaning function, minimize
the labor, easing of removability. This is our featured product. Since it comes
to the market, it attracts customers' attention.
Combine
Grain Cleaning Machine function:
Removing coated wheat husk in the wheat
huller.
Remove dust, light impurity by double air screen cleaners. Cyclone collects
dust, stalk, and husk.
Remove big, small impurity in the pre cleaner.
Remove immature, eaten, sicken, moldy ones
from healthy seeds on the gravity table.
Remove big, small impurity and grade seeds
in the vibration sifter.
Seed cleaning & processing machine
working flow:
Firstly wheat is fed from wheat huller
hopper. After hulling, wheat is transferred by Bucket Elevator to precleaning
sieving trunk for removing big and small impurity. There are two air screens at
this sieving trunk two ends and connect air pipes. The dust cleaning system
will remove the light impurity from grain twice before grain flow to gravity
table. Then grain seed enter to the gravity table for removing the bad seeds.
After Gravity Separator density separating, the seeds flow to main sieving
trunk. In this main sieve trunk, the oversize impurity, undersize impurity will
be removed. At same time, the sieve trunk can grade wheat to different size
ranks.
Grain cleaning & Processing Machine has
many adjusting handles. With these adjusting handles, operators can easily find
the suitable air volume, vibration amplitude. Machine is user friendly and
simple maintain.
We have 10 tons per hour and 20 tons per hour
model. The wheat huller is optional. If clients do not clean wheat, they
can order the model. The main sieve trunk we have two models: normal 4 sieve
layer one and two sieving deck one. If customer only uses the machine for
cleaning aim, no need to grade seeds by size, client can choose the two sieve
decks type.
5XZS-10DS
5XZS-10CDS
5XZS-20DS
5XZS-20CDS
Capacity (T/H)
10
10
20
20
Power (KW)
15.75
23.25
21.49
36.49
Size
(mm)
6500x2200x3600
6500x3200x3600
4730x2500x3830
5880x2500x3830
Weight (Kg)
2900
3200
2600
3000
Wheat hulling
NO
YES
NO
YES
Air cleaning
YES
YES
YES
YES
Gravity separating
YES
YES
YES
YES
Sieve cleaning
& Grading
YES
YES
YES
YES
Seed Cleaning & Processing Machine Seed Cleaning Machine,Seed Processing Machine,Seed Cleaning Processing Machine,Combine Seed Cleaning Machine SHIJIAZHUANG SYNMEC INTERNATIONAL TRADING LIMITED , https://www.seedgraincleaner.com
1. Due to the serious abrasion between the brake pin axle of the trailer and the axle hole of the brake shoe pin, the clearance becomes large, the brake shoe is not stable in the brake drum, and when the car bumps violently, the friction shoe on the brake shoe is Partial contact with the brake drum, resulting in friction resistance caused the wheel to "stunned."
2, the brake shoe return spring elasticity is insufficient, when the pedal is relaxed, after the brake cam returns, the friction plate is still in the braking position, the tire is in the braking state, resulting in the wheel "a daze."
3. When installing and adjusting the friction plate, the clearance between the friction plate and the brake drum is too small or there is no gap, and the wheel is in a semi-braked state and the wheel will be in a daze.
Method of exclusion:
1. If the wheel appears "a daze" in the transport operation, you can stop the car, step on the brake pedal a few times, or knock the brake drum. Loosen the car backwards and the wheel may turn.
2. If the wheels are "stunned" due to lack of return spring elasticity, replace the return springs and bearings.
3. If the brake pin shaft and the pin shaft hole are seriously worn out, parts can be replaced, and the worn shaft and hole can be rounded and a bushing can be added. In addition, the gap between the friction plate and the brake drum should be adjusted to normal. The tightness of the nut outside the bearing should be tightened in the end so that the bearing has no clearance but can be flexibly rotated.
